DAVIS Vantage Pro2 ISS Installationshandbuch PDF herunterladen

ANEMOMETER TRANSMITTER KIT

INSTALLATION MANUAL

This manual describes how to install the Anemometer Transmitter Kit for a Wire-

less Vantage Pro2

Weather Station. The kit enables you to connect the anemome-

ter from your Integrated Sensor Suite (ISS) to its own transmitter, so it can be

located away from the ISS and communicate directly with your console/receiver.

Components

The Anemometer Transmitter Kit includes the following components and mounting

hardware:

Tools for Setup

In addition to the kit, you will need some or all of the following materials:

• Adjustable wrench or 7/16" wrench

• Compass or local area map

• Ballpoint pen or paper clip (small pointed object of some kind)

• Drill and 3/16" (5 mm) drill bit (if mounting on a vertical surface)

• Carpenter’s level (if mounting on a vertical surface)

If You Are Installing the ISS and the Anemometer Transmitter Kit

at the Same Time

Install your ISS first, following the instructions in the ISS manual. However, during

the step “Preparing the ISS for Installation,” DO NOT connect the anemometer

cable to the SIM. When you have mounted the rain collector side of the ISS and are

ready to mount the anemometer, follow the instructions in this manual starting with

“Preparing the Anemometer Transmitter” on page 3.

1/4" Flat Washers

1/4" Lock Washers

1/4" Hex Nuts

3-Volt

Lithium

Battery

U-Bolts

1/4" x 1-1/2" Lag Screws

8" Cable Ties

Transmitter Shelter

6 x 1/2" (3.5 x 12 mm)

Self-Threading Screw

#6 Washer

Cable Clamp

1 2 3 4 5 6 ... 11 12

Inhaltsverzeichnis

Seite 1 - Tools for Setup

1ANEMOMETER TRANSMITTER KIT INSTALLATION MANUALThis manual describes how to install the Anemometer Transmitter Kit for a Wire-less Vantage Pro2TM

Seite 2 - Installation Steps

10A Note on Securing CablesTo prevent fraying or cutting of cables, secure them so they will not whip about in the wind. Secure a cable to a metal pol

Seite 3

11When replacing the cups, make sure they are not rubbing against any part of the anemometer head. “Wind readings aren’t what I expected them to be.”B

Seite 4 - DIP Switche

Product Numbers: 6332, 6332OVDavis Instruments Part Number: 07395.237 Anemometer Transmitter Kit Installation Manual Rev. A Manual (10/15/04)This prod

Seite 5 - Viewing Current Wind Data

2Installation StepsThe following is an outline of the steps necessary to install the Anemometer Trans-mitter Kit. These steps are used as section head

Seite 6 - Test Mode

33. Remove the hex nuts and washers holding the rain collector side on the pole. Retrieve the U-bolt that was holding the anemometer. 4. Using the was

Seite 7 - Mounting Anemometer on a Pole

45. Locate the DIP switches. You will work with them during the next installation step. Setting the Transmitter IDEach wireless transmitting station m

Seite 8 - 40' of Anemometer Cable

5Setting Console/Receiver(s) to Same ID1. Put your console into Setup Mode — press and hold DONE and press the DOWN arrow (-). The console will show y

Seite 9

6Test ModeDIP switch #4 on the SIM (see illustration on page 6) is the TEST DIP switch. Switch it to the ON position using a ball-point pen or paper c

Seite 10 - Cable Clip

7Range of Wireless TransmissionThe range of your radio transmission depends on many factors. Try to position the transmitter shelter and your console/

Seite 11 - Specifications

83. Swivel the ane-mometer until the arm is pointing north, if possible. 4. Using an adjust-able wrench or 7/16" wrench, tighten the nuts. If the

Seite 12

9Mounting Transmitter Shelter on a Pole1. While holding the shelter against the pole, place a U-bolt around the pole and through the two holes on at t