Davis DriveRight 600E GD/HD Installation Guide (8126GD, Bedienungsanleitung

Product # 8156GD, 8156HDGeneral-Duty &Heavy-DutyInstallation Manual

❏ The gap between the magnet mount and sensor must be 3/8”-1/2” (10-13mm). There should be a clearance zone of at least 3/4” (19mm) above the drive s

The bracket shown below provides a rigid mount for the speed sensor. At low speeds excessive vehicle vibrations can cause erroneous readings if the

Adjust the magnet mounting position so that the magnet passes opposite the tip of the sensor. Cinch magnet mount tie wrap tight against drive shaft.

3URFHGXUH,QVWDOOWKH+DUQHVV&DEOH&RQQHFW9'&3RZHUDQG*URXQG/HDGVDriveRight requires an unswitched +12 VDC power source.

&RQQHFW3RZHU*URXQGDQG6HQVRU/HDGVMake sure the wiring harness extends to the DriveRight console mounting location when making the followin

Connect the black ground wire from the adapter cable to chassis ground.Use in-line butt splices to connect the blue wires with fuses to the green a

7RSRI'DVKERDUG0RXQWLQJ2SWLRQVInstructions for Using Velcro®:Apply the two adhesive-backed Velcro loop tapes to the flats on the back of the

3URFHGXUH)LQLVKWKH,QVWDOODWLRQUse the following steps to finish the installation.&  It is not necessary to enter a code in order to perf

Then push the two connectors together. The connector housing on the console cable slides back when you make the connection, allowing the cables to l

7528%/(6+227,1*,QVWDOODWLRQ&KHFNOLVWUse the following list to check a professional DriveRight installation or to help spot potential problems

© Davis Instruments Corp. 1997-2003. All rights reserved.DriveRight General-Duty & Heavy-Duty Installation Manual Rev. D, November 7, 2003 Product

$QVZHUVWR&RPPRQ4XHVWLRQV“BAT” stays on when console is connected to harness cable.The wire connections to the harness cable are probably not

Knocking sounds are coming from under the vehicle.The magnet is hitting the vehicle or mounting bracket while rotating. Inspect the sensor installa

6833/(0(17)25'5,9(5,*+7+',QVWDOOWKH6SHHG6HQVRU0DJQHWUse these instructions to install the speed sensor magnet using a stainless ste

7LJKWHQ8VLQJWKH7HQVLRQ7RROThe Tension Tool, , operates like a screw-driver and is best used for single installations.Trim the stainless steel

3465 Diablo Avenue, Hayward, CA 94545-2778 U.S.A.510-732-9229 • Fax: 510-732-9188E-mail: [email protected] • www.davisnet.com:DUUDQW\5HSDLU,QIRU

,1752'8&7,21This manual provides installation instructions for the DriveRight 600 GD (General Duty), , and DriveRight 600 HD (Heavy Duty),

+DUQHVVDQG$GDSWHU&DEOHV:LULQJ6SHHG6HQVRU'ULYH5LJKW*'0DJQHW&  The speed sensor magnet is extremely strong and will de-mag

'ULYH5LJKW+'0DJQHWThe DriveRight HD speed sensor magnet includes the following components. See “Supplement for DriveRight HD” on page 20

3/$11,1*<285,167$//$7,21+RZ'ULYH5LJKW:RUNVDriveRight GD and HD use a a reed switch and rotating magnet to sense vehicle speed. The speed

Often you can route the sensor wires through an existing feedthrough in the firewall.❏ Decide where to install the harness cable and where to connec

,167$//,1*'5,9(5,*+7&  Always use safety stands when working under a raised vehicle. Never work under a vehicle supported only by a jack.3

Place the magnet in its mount, then slide the large tie wrap through the magnet mount to keep the magnet in place as shown below. Loosely cinch the