Davis Universal Anemometer Interface for Vantage Pro2 Bedienungsanleitung PDF herunterladen (Seite 10)

Configure the Console

Note: If your are not using an R.M. Young anemometer, you must use a Vantage Vue console. This con-

sole allows for the special calibration needed.

Vantage Pro2 Console

IfyouranemometerrequiredthatP2pins1&2beshunted(e.g.R.M.Young,see

page7)followtheseinstructionstoconfigureyourVantagePro2console:

1. EnterSetupModebypressingDONEandthe“‐”keyatthesametime.

2. PressandreleasetheDONEkeytoscrollthroughthesetupscreensuntil

WINDCUPSIZEappears.Pressthe“+”and“‐”keystoscrollthroughthe

windcupoptionsandselect“OTHER.”

Note: Early firmware versions may not have the OTHER option. You can update your firmware at

www.davisnet.com/support.

3. PressandholdDONEtoreturntothecurrentweatherscreen.

Vantage Vue Console

1. EnterSetupbypressingandreleasing2NDandthenSETUP.

2. PressandreleaseDONEuntilScreen6:TransmitterIDsappears.

•IfyourconsoleisreceivingfromaVantagePro2ISS,pressGRAPHtochange

thetypeofstationassignedto“VP2ISS.”

•IfyourconsoleisreceivingfromanAnemometerTransmitterKit,press

GRAPHtochangethetypeofstationassignedto“WIND.”

3. PressandreleaseDONEtoscrolltoScreen12:WindCupType.

4. Pressthe“+”and“‐”keystoscrollthroughthethreewindcupoptionsand

select“OTHER.”

Note: If you are using an R.M. Young anemometer skip to Step 6.

5. IfyouranemometerrequiredthatP2pins2&3beshunted(e.g.notanR.M.

Young),youmustcalibratetheVantageVueconsole.Followtheseadditional

stepstodeterminethecalibrationnumberandcalibratetheconsole:



a.Reviewyouranemometer’sliteratureortechnicalspecificationstodeter‐

mineitstransferfunctionThetransferfunctionshouldbeinthefollowing

format:



V=(FxM)+B

V=Velocityinm/s(meterspersecond)

F=FrequencyinHz(hertz)orPPS(pulsespersecond)

MandB=Constants(definedintheanemometer’stransferfunction)

b.Calculateyourcalibrationnumber:Cal.No.=1000xM

Example:TheNRG40C/Max40anemometerhasatransferfunctionof



V=(Fx0.756)+0.35.Thereforethecalibrationnumberis1000x0.756,or0756.



c.Ontheconsole,press2NDandGRAPHtodisplay

“WINDCALNUMBER”.

d.Pressthe“<“,“>”,“+”and“‐”keystoselectthenumberderivedabove.

6. PressandholdDONEtoreturntothecurrentweatherscreen.

1 2 ... 5 6 7 8 9 10 11 12

Kommentare zu diesen Handbüchern

Keine Kommentare

Davis Universal Anemometer Interface for Vantage Pro2 Bedienungsanleitung Seite 10

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Thermometer Davis Universal Anemometer Interface for Vantage Pro2